CADMEN world:2009年5月

MENPITA

menpita (2009年5月20日 16:34)

world CADMEN

MENPITA

(JAPANESE STYLE CAD-COUNTER-PLATE SETTER)

MANPITA-PRO

♦NEW DIE & USED DIE IN POSSIBLE

♦VERY EAZY!
♦VERY ACCRETE!
♦VERY SPEEDY!
♦MOREOVER SIMPLE!!!

*CONTENT OF SET*
	•PIN	30PIE
	•GUIDE	10PIE
	•PUSH RING	4PIE
	•MARK	30PIE
	•CONER BORD	10PIE

MANPITA

♦ONLY NEW DEI IN POSSIBLE

♦VERY EAZY!
♦VERY ACCRETE!
♦VERY SPEEDY!
♦MOREOVER SIMPLE!!!

*CONTENT OF SET*
	•PIN	30PIE
	•GUIDE	10PIE
	•PUSH RING	4PIE
	•MARK	30PIE

▼YOUTUBE HERE CLIC!!

	MAKE A BOX! ■ MAIN OFFICE 〒921-8015 79 TOURIKI KANAZAWA ISHIKAWA JAPAN TEL +81-76-291-0035　FAX +81-76-291-0847

■CADMEN world >

The accuracy problem of a DieCutting machine

menpita (2009年5月20日 03:24)

CADMEN

world

If the clearance of Chace and DirCutting machine is large,-

it will rotate, or there is gap to depth.

Since the matrix TAPE itself shifts well and it comes to a center so that it may go into a center, the DieCutting spot which does not recognize DieCutting machine accuracy has very many matrices tape.
Please check by the following method.

When inaccurate, adjustment is required of the DIECUTTINGMACHINE maker

①

DIE is attached in CHACE and it puts into the inside of a plane.

②

CUTTINGPLATE is pulled out, and a broad tape is stuck on "the part where knife hits" so that "the direction of length" and a "transverse direction" of STEELRULE may be covered.

③

CUTTINGPLATE is put in and it is a line chair about 1 time and a press.

④

CHACE is pulled out and CHACE is put in again.
　(It is better for pulling out to pull out the whole CHACE.) It may be hard to come out of an error if it is a short drawer distance.

⑤

Again, it presses.

⑥

4-5 are repeated about 3 times.

⑦

CUTTINGPLATE is pulled out and "the marks of knife" attached to the tape is checked.

⑧

If all "marks of a knife" is located in the same position, a problem is not in accuracy.

The accuracy of DIECUTTINGMACHINE is poor if the position of a knife has shifted. Please carry out an adjustment request at the DIECUTTINGMACHINE maker.

■CADMEN world >

How to strike of DieRing

menpita (2009年5月17日 07:31)

CADMEN			world

Attention when DieRing is put in Die

Please embed DieRing correctly at Die	1.	Good
	2.	Do not put it as it is stiff.
Please do not strike DieRing with a direct	3.	should not. in the state that DieRing dashes out
hammer on Diebord.	4.	DieRing must not put it in the interior of Die.

■CADMEN world >

The arrangement method of DIE-RING

menpita (2009年5月17日 07:30)

CADMEN

world

Method of arranging DIERING

The hole arrangement of the hole of Die-ring is different in RIPITA and usual Counter-plate.

Hanging down occurs in Counter-plate of the double-faced tape and it doesn't become Cutting-plate from externals to touch and to put it on if it doesn't suppress it to 250mm or less between Die-ring holes within 125mm usually. (Though it is somewhat good. )

When the hole of 250mm in the diameter is drawn from Diering, it is comprehensible.

Basic chart

Explanation) The basis is assumed to be 2 piece transcript. If yen of 250mm can be covered, it usually takes account very much though it is OK, the hole position of Diering is centered to the last, and Counter-plate of the double-faced tape is pushed in. It pushes it in without thinking about anything for Ripita.

Dividing is easy shape to set.

The explanation) It is produced to divide into two by the front page in a big thing of AMERIKANROCK and BOTTUMROCK, and there is no uselessness and COUNTERPLATE can be produced.

It is necessary to clear the hole another one three so that there is a center part when it is usual two sided tape addition COUNTERPLATE ..hanging down turning over [duki].. though two four of the 2nd and 3 in RIPITA can be arranged.

Arrangement method in front page

Explanation) It bonds when it is usual two sided tape addition COUNTERPLATE and it distorts though it is arranged accurately after pushing at the position of MENPITA even if upper right and the part under the left touch in RIPITA. It wishes without fail by arranging 4 pieces.

■CADMEN world >

FRONT

menpita (2009年5月17日 07:29)

CADMEN			world

CADMENworld aims at getting rid of from the matrix tape with low productiy.

MENPIT		RIPITA

	MENPITA It changed it into the work quite different from the transcript method of installing COUNTER-PLATE in Die with the pin put on CUTTING-PLATE. It is a transcript method of the birth in Japan.

RIPITA RIPITA-COUNTER-PLATE is a reuse plate that can be recycled by easily peeling off. Stocks-plate is not needed. The angel hair can be prevented being generated.
CADMENworld

■CADMEN world >

►The accuracy problem of a milling machine

menpita (2009年5月17日 07:28)

CADMEN

world

►The discovery method when the machine accuracy of milling which makes COUNTER-PLATE is bad.

It is necessary to check the accuracy of the machine before-

CounterPlate is made.

（Accuracy doesn't go out of CounterPlate and MENPITA if accuracy has not gone out to the machine. ）

It improves it by the numerical correction if it says to machinery manufacturer.

①

　Following CounterPlate is made with the machine.

　The hole of 22mm pies per four corner of 300mm corner is cleared in 30mm.

Attention...Please make the hole of 22mm pies tight a little so that there is no space in the Guide.

②

　The seal is removed in horizontal respect such as 1 and desks and Patch is bonded.

③

It covers Patch with Guide.

④

　It puts a Patch in "Another Guide", and the seal is removed.

Attention...Please put the hardboard of the collection in the Guide when the height of the Patch is low. The Guide shifts when bonding is weak.

⑤

It transcribes in the hole of COUNTER-PLATE and after MENPITA-GUIDE of "4" is put, the mark is transcribed in MENPITA-GUIDE of "2" ..including the difference it as for the hole of COUNTER-PLATE...

⑥

　The MENPITA-MARK and the MENPITA-GUIDE of two holes of the remainder are similarly transcribed.

⑦

　COUNTERPLATE is the horizontal compared with the stand and it is confirmed to record without difficulty.

⑧

　Please confirm the thing not distorted.

⑨

　Next, COUNTERPLATE is rotated in "90°", and it puts it on the MENPITA-GUIDE.

Moreover, please return and confirm the back while turning.

⑩

The accuracy of "Length" and "Side" of MILLING-MACHIN will not have gone out when COUNTER-PLATE is abnormally distorted at this time or resistance is large.

⑪

Please inquire of the MILLINGMACHIN manufacturer if abnormality that COUNTERPLATE is distorted and enters is found in the MENPITA-GUIDE.

■CADMEN world >

►The arrangement method of DIE-RING

menpita (2009年5月17日 07:26)

CADMEN	world
►The arrangement method of DIE-RING

■CADMEN world >

MENPITA WORK PROCEDURE

menpita (2009年5月17日 07:06)

CADMEN	world

chess
Guide pin
Mark
MENPITA-KUN WORK PROCEDURE

①Clean off the adhesive on the cutting-plate
with thinner.

②Put the “Mark”(round shape transcription ) in
round gutter of “Convex of Menpita-kun”.
(put it on release exfolitation paper side has
to be faced up)

③Insert the “Convex of Menpita-kun” into
“Concave of Menpita-kun”, and make half
turn clockwise, and take off attached
exfolitation paper.

④
Push into Chess and press it one time.
(Machine pressure is normal cut pressure)
⑤
Pull out the cutting-plate from inside of the machine,
and check if all “Marks” transferred the cutting-plate
or not. Make half turn “Convex of Menpita-kun”
clockwise, and take it out.( Keep this for reuse next
time)
⑦
Insert the “Guide pin” in the hole of counter-plate.
Counter-plate stops at the taper of “Guide pin”.
(Height approximately 4mm)
⑨
Take out "Guide pin" and "Mark" from the cutting-plate
and wipe the counter-plate with rag ( Keep this for reuse
next time) and work completion.
⑥
Set it on “Mark” on the cutting-plate like covering
"Guide pin". Be sure not to make a gap between the
cutting-plate and guide pin.
⑧
Cover the "Ring" on "Guide pin", and push the
counter-plate to the point of root, and transfer it.

■CADMEN world > product >

CAD-COUNTER-PLATE

menpita (2009年5月17日 00:36)

CADMEN	world

■CADMEN world > product >

MENPITA

menpita (2009年5月17日 00:31)

CADMEN		world

MENPITA was devised in Japan, in order to set REPITA-COUNTER-PLATE early correctly.
(RIPITA-COUNTER-PLATE is CAD-COUNTER-PLATE of the weak-
sticking that CADMENworld offers of pasting and can the peel.)

MANPITA has three kinds of kits
	►MENPITA-PRO kit	New Die & used Die in possible	click!
	►MENPITA kit	Only new Die in possible	click!
	►MENPITA+ kit	The part for helping a used Die	click!

How to make Die
	►The arrangement method of DIE-RING		click!
	►DIE-RING is attached in Die		click!

MENPITA WORK PROCEDURE
►The transfer method of REPITA-COUNTER-PLATE in Die-cutter--mashin (illasut)			click!
►The transfer method of RIPITA-COUNTER-PLATE in Die-cutter--mashin (picture)			click!

Supposing CREASING does not work ...
	►The discovery method when the machine accuracy of meeling-
	which makes CounterPlate is bad.		click!
	►The discovery method when the accuracy of CuttingPlate and Chase is bad .		click!
	►When the way with PUSHRING to push is bad, -
	REPITA-COUNTER-PLATE cannot be positioned accurately.		click!
	►When using it excluding RIPITA-COUNTER-PLATE.		click!

2009年5月：CADMEN world

MEN-PITA promises all reduction in costs and high qualitys of die-cutting.

2009年5月アーカイブ

MENPITA

The accuracy problem of a DieCutting machine

How to strike of DieRing

The arrangement method of DIE-RING

FRONT

►The accuracy problem of a milling machine

►The arrangement method of DIE-RING

MENPITA WORK PROCEDURE

CAD-COUNTER-PLATE

MENPITA

Contents

Contact Us

Search

Social Bookmark

2009年5月：CADMEN world

2009年5月アーカイブ

Contents

Contact Us

Search

Tag cloud

Social Bookmark