CADMEN world

MENPITA

2009-05-20T07:34:35Z

world CADMEN

MENPITA

(JAPANESE STYLE CAD-COUNTER-PLATE SETTER)

MANPITA-PRO

♦NEW DIE & USED DIE IN POSSIBLE

♦VERY EAZY!
♦VERY ACCRETE!
♦VERY SPEEDY!
♦MOREOVER SIMPLE!!!

*CONTENT OF SET*
	•PIN	30PIE
	•GUIDE	10PIE
	•PUSH RING	4PIE
	•MARK	30PIE
	•CONER BORD	10PIE

MANPITA

♦ONLY NEW DEI IN POSSIBLE

♦VERY EAZY!
♦VERY ACCRETE!
♦VERY SPEEDY!
♦MOREOVER SIMPLE!!!

*CONTENT OF SET*
	•PIN	30PIE
	•GUIDE	10PIE
	•PUSH RING	4PIE
	•MARK	30PIE

▼YOUTUBE HERE CLIC!!

	MAKE A BOX! ■ MAIN OFFICE 〒921-8015 79 TOURIKI KANAZAWA ISHIKAWA JAPAN TEL +81-76-291-0035　FAX +81-76-291-0847

The accuracy problem of a DieCutting machine

2009-05-19T18:24:21Z

CADMEN

world

If the clearance of Chace and DirCutting machine is large,-

it will rotate, or there is gap to depth.

Since the matrix TAPE itself shifts well and it comes to a center so that it may go into a center, the DieCutting spot which does not recognize DieCutting machine accuracy has very many matrices tape.
Please check by the following method.

When inaccurate, adjustment is required of the DIECUTTINGMACHINE maker

①

DIE is attached in CHACE and it puts into the inside of a plane.

②

CUTTINGPLATE is pulled out, and a broad tape is stuck on "the part where knife hits" so that "the direction of length" and a "transverse direction" of STEELRULE may be covered.

③

CUTTINGPLATE is put in and it is a line chair about 1 time and a press.

④

CHACE is pulled out and CHACE is put in again.
　(It is better for pulling out to pull out the whole CHACE.) It may be hard to come out of an error if it is a short drawer distance.

⑤

Again, it presses.

⑥

4-5 are repeated about 3 times.

⑦

CUTTINGPLATE is pulled out and "the marks of knife" attached to the tape is checked.

⑧

If all "marks of a knife" is located in the same position, a problem is not in accuracy.

The accuracy of DIECUTTINGMACHINE is poor if the position of a knife has shifted. Please carry out an adjustment request at the DIECUTTINGMACHINE maker.

How to strike of DieRing

2009-05-16T22:31:32Z

CADMEN			world

Attention when DieRing is put in Die

Please embed DieRing correctly at Die	1.	Good
	2.	Do not put it as it is stiff.
Please do not strike DieRing with a direct	3.	should not. in the state that DieRing dashes out
hammer on Diebord.	4.	DieRing must not put it in the interior of Die.

The arrangement method of DIE-RING

2009-05-16T22:30:41Z

CADMEN

world

Method of arranging DIERING

The hole arrangement of the hole of Die-ring is different in RIPITA and usual Counter-plate.

Hanging down occurs in Counter-plate of the double-faced tape and it doesn't become Cutting-plate from externals to touch and to put it on if it doesn't suppress it to 250mm or less between Die-ring holes within 125mm usually. (Though it is somewhat good. )

When the hole of 250mm in the diameter is drawn from Diering, it is comprehensible.

Basic chart

Explanation) The basis is assumed to be 2 piece transcript. If yen of 250mm can be covered, it usually takes account very much though it is OK, the hole position of Diering is centered to the last, and Counter-plate of the double-faced tape is pushed in. It pushes it in without thinking about anything for Ripita.

Dividing is easy shape to set.

The explanation) It is produced to divide into two by the front page in a big thing of AMERIKANROCK and BOTTUMROCK, and there is no uselessness and COUNTERPLATE can be produced.

It is necessary to clear the hole another one three so that there is a center part when it is usual two sided tape addition COUNTERPLATE ..hanging down turning over [duki].. though two four of the 2nd and 3 in RIPITA can be arranged.

Arrangement method in front page

Explanation) It bonds when it is usual two sided tape addition COUNTERPLATE and it distorts though it is arranged accurately after pushing at the position of MENPITA even if upper right and the part under the left touch in RIPITA. It wishes without fail by arranging 4 pieces.

FRONT

2009-05-16T22:29:54Z

CADMEN			world

CADMENworld aims at getting rid of from the matrix tape with low productiy.

MENPIT		RIPITA

	MENPITA It changed it into the work quite different from the transcript method of installing COUNTER-PLATE in Die with the pin put on CUTTING-PLATE. It is a transcript method of the birth in Japan.

RIPITA RIPITA-COUNTER-PLATE is a reuse plate that can be recycled by easily peeling off. Stocks-plate is not needed. The angel hair can be prevented being generated.
CADMENworld

►The accuracy problem of a milling machine

2009-05-16T22:28:10Z

CADMEN

world

►The discovery method when the machine accuracy of milling which makes COUNTER-PLATE is bad.

It is necessary to check the accuracy of the machine before-

CounterPlate is made.

（Accuracy doesn't go out of CounterPlate and MENPITA if accuracy has not gone out to the machine. ）

It improves it by the numerical correction if it says to machinery manufacturer.

①

　Following CounterPlate is made with the machine.

　The hole of 22mm pies per four corner of 300mm corner is cleared in 30mm.

Attention...Please make the hole of 22mm pies tight a little so that there is no space in the Guide.

②

　The seal is removed in horizontal respect such as 1 and desks and Patch is bonded.

③

It covers Patch with Guide.

④

　It puts a Patch in "Another Guide", and the seal is removed.

Attention...Please put the hardboard of the collection in the Guide when the height of the Patch is low. The Guide shifts when bonding is weak.

⑤

It transcribes in the hole of COUNTER-PLATE and after MENPITA-GUIDE of "4" is put, the mark is transcribed in MENPITA-GUIDE of "2" ..including the difference it as for the hole of COUNTER-PLATE...

⑥

　The MENPITA-MARK and the MENPITA-GUIDE of two holes of the remainder are similarly transcribed.

⑦

　COUNTERPLATE is the horizontal compared with the stand and it is confirmed to record without difficulty.

⑧

　Please confirm the thing not distorted.

⑨

　Next, COUNTERPLATE is rotated in "90°", and it puts it on the MENPITA-GUIDE.

Moreover, please return and confirm the back while turning.

⑩

The accuracy of "Length" and "Side" of MILLING-MACHIN will not have gone out when COUNTER-PLATE is abnormally distorted at this time or resistance is large.

⑪

Please inquire of the MILLINGMACHIN manufacturer if abnormality that COUNTERPLATE is distorted and enters is found in the MENPITA-GUIDE.

►The arrangement method of DIE-RING

2009-05-16T22:26:56Z

CADMEN	world
►The arrangement method of DIE-RING

MENPITA WORK PROCEDURE

2009-05-16T22:06:57Z

CADMEN	world

chess
Guide pin
Mark
MENPITA-KUN WORK PROCEDURE

①Clean off the adhesive on the cutting-plate
with thinner.

②Put the “Mark”(round shape transcription ) in
round gutter of “Convex of Menpita-kun”.
(put it on release exfolitation paper side has
to be faced up)

③Insert the “Convex of Menpita-kun” into
“Concave of Menpita-kun”, and make half
turn clockwise, and take off attached
exfolitation paper.

④
Push into Chess and press it one time.
(Machine pressure is normal cut pressure)
⑤
Pull out the cutting-plate from inside of the machine,
and check if all “Marks” transferred the cutting-plate
or not. Make half turn “Convex of Menpita-kun”
clockwise, and take it out.( Keep this for reuse next
time)
⑦
Insert the “Guide pin” in the hole of counter-plate.
Counter-plate stops at the taper of “Guide pin”.
(Height approximately 4mm)
⑨
Take out "Guide pin" and "Mark" from the cutting-plate
and wipe the counter-plate with rag ( Keep this for reuse
next time) and work completion.
⑥
Set it on “Mark” on the cutting-plate like covering
"Guide pin". Be sure not to make a gap between the
cutting-plate and guide pin.
⑧
Cover the "Ring" on "Guide pin", and push the
counter-plate to the point of root, and transfer it.

CAD-COUNTER-PLATE

2009-05-16T15:36:33Z

CADMEN	world

MENPITA

2009-05-16T15:31:36Z

CADMEN		world

MENPITA was devised in Japan, in order to set REPITA-COUNTER-PLATE early correctly.
(RIPITA-COUNTER-PLATE is CAD-COUNTER-PLATE of the weak-
sticking that CADMENworld offers of pasting and can the peel.)

MANPITA has three kinds of kits
	►MENPITA-PRO kit	New Die & used Die in possible	click!
	►MENPITA kit	Only new Die in possible	click!
	►MENPITA+ kit	The part for helping a used Die	click!

How to make Die
	►The arrangement method of DIE-RING		click!
	►DIE-RING is attached in Die		click!

MENPITA WORK PROCEDURE
►The transfer method of REPITA-COUNTER-PLATE in Die-cutter--mashin (illasut)			click!
►The transfer method of RIPITA-COUNTER-PLATE in Die-cutter--mashin (picture)			click!

Supposing CREASING does not work ...
	►The discovery method when the machine accuracy of meeling-
	which makes CounterPlate is bad.		click!
	►The discovery method when the accuracy of CuttingPlate and Chase is bad .		click!
	►When the way with PUSHRING to push is bad, -
	REPITA-COUNTER-PLATE cannot be positioned accurately.		click!
	►When using it excluding RIPITA-COUNTER-PLATE.		click!

We will promise the improvement of the quality and productivity.

2009-03-25T17:07:02Z

CADMEN world
	COMMPANY	MAKE A BOX ! CO.LTD
	ADDORESS	79 TOURIKI KANADAWA ISHIKAWA JAPAN
	TEL / FAX	+8176 291 0035 +8176 291 0847
	HP	http://world.cadmen.jp
	MAIL	info@cadmen.jp

Our company is a bright, energetic small and medium-sized enterprise. Information is sent by using MTOS in the future.

The inquiry : from the mail form to our company please.

2009-03-25T04:00:00Z

【Attention】

To transmit this mail form by CGI for UTF-8, a part of character might be garbled. Moreover, mail might not be able to be sent well with a part of model like carrying etc. according to this form.
It will ask here with mail in that case.

mail-address*
Name*
Address*
Business*
Confirmation		Please check it when you can do the above-mentioned confirmation.

		*Required item